Field service manual i885

Willis Gregory, aka singleshot. All Rights Reserved. Page completed in 0. Welcome, Guest. Please Login or Register. Pages: 1. Lift the SD card lock. Slide SD Card outward. Being careful not to touch the contacts.

Remove the Back Housing from the unit by lifting from the top and disengaging the snaps on both sides. Remove the Battery Frame from the unit. Remove the Bluetooth antenna from the Main Board. Remove the main board from the Front housing and disconnect the flex. Remove the Main Antenna and Bluetooth antenna from the Unit. Separate the Flip Flex from the front housing. Unfold the flex of the front housing.

Lift the Hinge out of the front housing. Carefully remove the flip assembly from the front housing using care not to damage the flex. Tools Required: None Required 1. Apply the Main Board label. Apply the water indicator to the main board and ensure it is in the proper place. Assemble two Contact EMI shield to the point of main board. Apply the battery label in the battery cavity. Apply 3 poron pads onto the front housing.

Apply a poron pad to the keypad Hinge Flex on the tip of the flex in the front housing. Assemble the hinge button into the front housing with tweezers Ensure proper direction as shown. Assemble the ring in the FH. Use the bottom of the tweezers to press the ring Ensure the ridge of the ring is in the slot of Front Housing correctly. Insert the hinge mechanism into the flip housing. Ensure correct orientation. Align the Flip with the ring in the Front Housing.

Align the hole on the hinge collar against the anchor point on the front housing, then close the flip slowly. Connect the Flex connector to the Front Housing Connector. Apply the conductive poron on the location as shown. Assemble the USB seal to the front housing. Assemble the Main Antenna into the front housing. Assemble the main board to Front Housing as shown.. Assemble the Bluetooth Antenna into the Front Housing.

Apply the conductive poron pad to the Battery Frame. Ensure the right end of the frame in the proper location. Assemble the Battery Frame to Front Housing from right to left and ensure the hinge connector was covered by frame completely. Apply the radio label on the front housing.

Apply the battery pad using tweezers to the Back Housing. Assemble the SD card seal to back housing and ensure the inverse side is up. Assemble the rear housing to the front housing. Place the unit into the Screw Nest Fixture D Insert the Six T-5 Screws and fasten in the order shown. Slide SD Card inward. Align the SIM Card as shown 4. Push the SIM card toward the Bottom of the unit. Tilt the back of the battery at approximately a 45 degree angle and insert into the Back Housing.

Push the battery toward the bottom of the unit and push the back of the battery down 3. Place the Battery door on the unit where it aligns with the Back Housing. Slide battery door towards Top of unit. Yes Disconnect power supply. Connect flash cable to PC. Comm Check with XFlash. Yes FX2 replaced? Use this test on a unit with the following symptom: no RX. The level will be low.

Adjust the spectrum analyzer accordingly. Check for a bad connection from the VCO module to the radio board. Yes Yes Check band select lines. For band, voltage at C is low and voltage at C is high. For band, voltage at C is high and voltage at C is low.

The FGU is working properly. Check that the voltage at C pin 9 is between 0. There is no issue with the control voltage. Check for opens, shorts, or missing components in the loop filter. Ensure the correct band select is chosen. Check L for 2. Check the voltage on C and C Set the spectrum analyzer to Center Freq: Set marker to test frequency, and use Trace and Max. Hold to obtain readings. Use Clear before taking each reading. Except as noted, use a ohm probe for all RF measurements.

The probe ground must make contact with the board ground during the measurements. Be sure to check for any defects, such as unsoldered connections, shorts, broken or defective components.

Remove the antenna from the UUT before beginning these tests. Yes Check the voltages on positive terminal of C negative terminal always 0V No. Do the following: 1. Measure the RF level at the antenna port. Note: Perform the Transmit Power Test before beginning this test. Set the unit to the Open Loop Power Test at Yes Do the following: 1. Set the Power Tune softpot to max auto power. Measure the RF power level at the antenna port. Set the unit to the TX. Power Tune Test 2. Set the Power Tune.

Measure the RF power. Check for open traces. Check C, R and E for defective components. Check C, R and E Check C and R , for defective components. Set the Power Tune softpot to Max power 3. Monitor the RF waveform at the antenna port. Check for the correct phase and amplitude train waveform.

Check that the modulation peaks are lower than the amplitude training ramp peak. Visually check all components and solder connections. Check R and R for 2. No Is the signal at Use this test on a unit with the following symptom: no SW1 1. Check for SW1 after L from U Test Setup 1. Amplitude levels above dBm will compress the Janus IC. Remove the antenna and replace it with a 50 OHM coax. An Audio Test Cable is required to complete test mode correctly.

MA Test mode is achieved by starting from a power-down condition: 1. Press and hold three keys in a row such as , , , -O-. Simultaneously, press the Power key 2. Release all keys once the opening screen appears in the main display. Follow instructions as they appear pressing the indicated keys. No instruction? Press any key or Scroll right. No reaction? Power down the unit, check battery condition, and start MA Test again.

Screen displays are depicted as follows:. The gray scale test image is from total black to white indicates that the display has no issues. Press any key to advance. The 4 internal borders are one-pixel wide and white. The rest except text are black. Close the flip to continue.

Color bar pattern is displayed on the modules to capture missing colors. Press any key to continue. Press any key to advance Ext key test. Check for the LED functionally. Morphing key turn on. All keys indicators are turned on. As each key is pressed, a short time vibration is felt and the key symbol on the CID disappeared. Continue until the entire keys have been pressed. Once all keys are pressed all key indicator LEDs on touch pad turn off. Proceed with flip open. If test fail, hit the mute key to skip.

CID displays Open Flip. And the 4 internal borders are one-pixel wide and white. Open the flip to continue. Verify backlight and vibration. Right Speaker tone displayed and speaker tone was generated. Verifty speaker tone.

Press Volume Up to continue. Left Speaker tone displayed and speaker tone was generated. Press Volume Down to continue. Right and Left Speaker tone displayed and speaker tone was generated. Press PTT to continue. If the photosensor fail to function or user didnt follow the instruction, this screen will appear for retest.

Remove the SD card to continue. The radio will detect if a SIM has been placed in the radio and report the result on the display. Display all keys i. As each key is pressed, the number disappears from the display. When all the keys are pressed, proceed to next test. Close the flip proceed. If the correct numbers cannot be located, call Motorola Parts Identification at Part No. Component Locations [Continued] Ref.

Replacement parts and kits for i units can be ordered directly from the Motorola Accessories and Aftermarket Division AAD at and listen to the prompts; or FAX If the correct part number cannot be located, call Motorola Parts Identification at If the correct number cannot be located, call Motorola Parts Identification at Refer to the exploded view and parts list in Chapter 7.

Table: A Recommended Test Tools. Table A RVN4 RVN4 Programs a laptop, handheld device, or desktop computer to use the i unit as a modem to transfer circuit or packet data.

Allows i units GPS feature to provide approximate location data to a laptop computer or other device. Pular no carrossel. Anterior no carrossel. Explorar E-books. Os mais vendidos Escolhas dos editores Todos os e-books. Explorar Audiolivros. Os mais vendidos Escolhas dos editores Todos os audiolivros. Explorar Revistas. Escolhas dos editores Todas as revistas. Explorar Podcasts Todos os podcasts. Explorar Documentos. Manual Ferrari I Enviado por Ian Vaera. Denunciar este documento.

Fazer o download agora mesmo. Salvar Salvar manual ferrari i para ler mais tarde. Chapter 1 Introduction to Electronic Communication Pesquisar no documento. Copyright , Motorola, Inc. All rights reserved. It's definitely isn't instant download so beware and they don't answer there customer support. Support contacted me and if I wanted my money back or still download the manual. I downloaded the manual with no problems thank you for your time to fix this matter.

Purchased manual was received quickly, and though while the original download link was for the incorrect manual, it was quickly replaced and resent with the right one without hassle. Very appreciated. Skip to navigation Skip to content Email us: [email protected]. Send us a request [email protected] Social Facebook Twitter Instagram. Rated 5 out of 5 based on 77 customer ratings.

Add to wishlist. Guaranteed Safe Checkout. Please consult your local distributor for those items you may require. Materials and specifications are subject to change without notice. Operators and maintenance personnel must read this manual before operating or maintaining this machine. This manual should be kept near the machine for reference and periodically reviewed by all personnel who will come into contact with it. This manual presented for you in electronic format you can just print out the page you need then dispose of it when you have completed your task.

This manual has detailed illustrations, parts name, parts number. It is very helpful for assembly or disassembly task or learn machine structure. This manual is compatible with the following computer operating systems: All Windows version All Mac version You need the adobe Acrobat reader to view the document as the manual is pdf format.

With PDF file you can print unlimited copies. You will be received download link after payment. What customer say about us! The item is that i want but the booklet fastener is not strong. Now i set up another device. If an obstruction is seen, no matter how small it may be, clean the bore with a cleaning rod and patch as described [in your firearm's owner's manual].

If your firearm fails to fire, keep the muzzle pointed in a safe direction for a minimum of 30 seconds. Rotate the ejection area of the firearm away from you, carefully open the action and remove the shell from the chamber. If the primer is indented, the defective shell should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction corrected before further use.

Glance down the barrel to make sure that no obstructions remain in the barrel. Completely clear the barrel before loading and firing again. Failure to follow these instructions can cause extensive damage to your firearm and possible serious injury to yourself and others. The caliber or gauge of your firearm is marked on the barrel. Store all catridges of different calibers or gauges in completely separate and well-marked containers. Never store cartridges of mixed calibers or gauges in a common container or in your pockets.

See your firearm's owner's manual] for more information on the correct ammunition for your firearm. We assume no responsibility for the use of unsafe or improper firearm and ammunition combinations or damage or injury caused by damaged ammunition.

See [your firearm's owner's manual] for more information on the correct ammunition for your firearm. However, we assume no responsibility for incidents which occur through the use of cartridges of nonstandard dimension or those developing pressures in excess of SAAMI established standards.

Treat every firearm with the respect due a loaded firearm, even though you are certain the firearm is unloaded. Know the range of your ammunition. Never shoot at water or hard objects.

Never place your firearm on or against a fence, tree, car or other similar object. If you observe other shooters violating any of these safety precautions, politely suggest safer handling practices. Special and extreme care should be taken to be sure your firearm is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition.

Closely supervise newcomers to the shooting sports. Encourage enrollment in hunting and shooting safety courses. Your vision, motor skills and judgment could be dangerously impaired, making your gun handling unsafe to you and to others.

It is your responsibility to secure the most up-to-date information on the safe handling procedures of your Browning firearm. We assume no liability for incidents which occur when unsafe or improper firearm accessories or ammunition combinations are used.